• General Specification Information
• TECTUS System New Models Brochure
• TECTUS TE 527 3D Data Sheet
• TECTUS TE 527 3D Fitting Instructions
• TECTUS TE 527 3D Door Load Specifications Guide
• CAD Drawings
• Door Throw [ dxf ]
• Open Hinge View [ pdf | dxf ]
• Block Frame [ pdf | dxf ]
• Casing Frame [ pdf | dxf ]
• Steel Frame [ pdf | dxf ]
• Milling Template Data
• Block Frame [ pdf | dxf ]
• Casing Frame [ pdf | dxf ]
• Steel Frame [ pdf | dxf ]
• Presentation Images
• Open Hinge View-High Resolution
• Certifications
• UL Listing : Certification Documents
• TECTUS Installation Video

Installation Tools and Accessories:

• Routing Templates
• Mounting Accessories
• Other Information

See TECTUS Tools and Accessories for more information (and installation images and video) on installing Tectus 3D concealed hinges in block, casing, steel, and aluminum frames.

Frequently Asked Questions about TECTUS® hinges.

Is the listed capacity for each hinge or for a pair?

The capacities listed below are for two TECTUS® hinges installed. They are engineered to work best when there are two.

 

TE 240 3D : 88 lbs. (40 kg)

TE 340 3D : 176 lbs. (80 kg)

TE 540 3D : 264 lbs. (120kg)

TE 540 3D A8 : 220 lbs. (100kg)

TE 640 3D : 440 lbs. (200kg)

TE 640 3D A8 : 352 lbs. (160kg)

TE 525 3D Series : 264 lbs. (120kg)

All Energy hinges retain their non-Energy model's capacity.

Can I get a greater load capacity by adding hinges?

At this time Simonswerk is reviewing this question as we've been asked this quite often. As listed above, the capacities are for the installation of two hinges. For the moment, if greater capacity is required, use the next hinge in the line.

However, it should be noted here that the rated capacity must be reduced for doors over 39 inches in width. For guidance in either of these situations, please contact us to discuss your options.

Where do I place the hinges on the door?

Top and bottom hinges should be located 10" (on center) from the top and bottom edge of the door. Unlike with Soss hinges, a third TECTUS® hinge will not add capacity to the system. With taller doors, installers often use a third hinge in the center.

What's the minimum thickness for each of the hinges?

Download Door Thickness Reference Document

 

TE 240 3D : 1"

TE 340 3D : 1-3/8"

TE 540 3D : 1-5/8"

TE 540 3D A8 : 1-7/8"

TE 640 3D : 1-5/8"

TE 640 3D A8 : 1-7/8"

TE 525 3D Series : 1-3/8"

Does the leading edge of the door need to be beveled?

This table shows the width, at given thicknesses, below which the latch side of a door fitted with Tectus® hinges requires an edge bevel. Please call us for further guidance.

Download Door Bevel Reference Document

TECTUS MODEL	THICKNESS	WIDTH
TE 240 3D	1"	8"
	1-3/8"	16"
TE 340 3D	1-3/8"	16"
	1-3/4"	28"
	2-1/4"	43"
TE 525 3D	1-3/8"	16"
	1-3/4"	28"
	2-1/4"	43"
TE 540 3D	1-3/4"	28"
	2"	32"
	2-1/4"	43"
TE 640 3D	1-3/4"	28"
	2"	32"
	2-1/4"	43"
TE 540 3D A8	2"	32"
(includes up to 5/16" cladding)	2-1/4"	43"
TE 640 3D A8	2"	32"
(includes up to 5/16" cladding)	2-1/4"	43"

Soss vs. TECTUS Concealed Hinges

Soss hinges are relatively inexpensive and may appear to be the better option if the cost of the individual hinge is the only measure. However, there are hidden costs which should be taken into consideration. The obvious technological difference is the ability to adjust the TECTUS hinge in 3 Dimensions. This allows for a much faster and more precise installation of the door. Now, if a door fitted with TECTUS needs to be tweaked, perhaps because the new building has settled, the installer need only get out his hex key and, with a few turns, bring the door back to flush. What we hear is that doors fitted with Soss frequently cause frequent call-backs requiring the door to be taken off and reworked or, worse, remade. Email us with any stories you have about your experience with Soss hinges.

 

Another consideration is the number of Soss hinges that need to be installed to achieve the higher capacities of the TECTUS® system. Check out the TECTUS vs OTHER CONCEALED HINGES cross reference guide for some examples.

Country of origin for Soss is Singapore. For Simonswerk TECTUS® it is Germany.

 

Customers who have used both have universally given the same feedback : significant savings are possible by using TECTUS® because the quicker and more precise installation of doors fitted with TECTUS® hinges and the nearly complete lack of call backs. We even have a few millworkers who strongly advocate using TECTUS® throughout a project, because they end up saving money for the owner.

Aesthetics is a matter of personal opinion, but we feel it's hard to argue against the more refined look and quality finishes available from Simonswerk's TECTUS®.

How many open-close cycles have the TECTUS® hinges been rated for?

The previous versions have been tested against ABHM BS EN 1935 and have received the highest rating of 200,000 cycles. The TE 340 3D hinge was recently tested to 1.5 million cycles (ANSI/BHMA). If your project requires more specific documentation, please contact us.

What are TECTUS® hinges made of?

Other than the TE 525 3D model, which is solid stainless steel, the main body of the other TECTUS hinges is cast in an aluminum alloy. The black plate that wraps around the hinge body is powder-coated steel. The coverplates are steel, and are finished to match the 'knuckle' of the hinge. All visible surfaces of the hinge match the specified finish.

Is there a minimum order for special order RAL tones?

Yes. Typically at least 100 hinges.

You can order these finish samples online!

	F1 : Satin Chrome Look [ 124 ] Finish Type : Powder-Coated Description : Gray/Silver ( view a comparison with F2 and SSL )
	F2 : Satin Nickel Look [ 125 ] Finish Type : Galvanic, Liquid-Coated Finish Description : Slightly Warmer Gray/Silver than F1 ( view a comparison with F1 and SSL )
	SSL : Stainless Steel Look [ 126 ] Finish Type : Powder-Coated Description : somewhat warmer, more champagne than standard US 32D  ( view a comparison with F1 and F2 )
	Rustic Umber [ 156 ] Finish Type : Powder Coated Description : US10B, matte, rich dark chocolate
	Bronze Metallic [ 168 ] Finish Type : Powder Coated Description : US10B, matte, rich dark chocolate
	Satin Nickel [ 144 ] Finish Type : Galvanic Plated Description :
	Polished Nickel [ 038 ] Finish Type : Galvanic Plated Description : buffed mirror
	Polished Brass [ 030 ] Finish Type : Galvanic Plated Description : beautiful
	Satin Chrome [ 040 ] Finish Type : Galvanic Plated Description : a good match to US 32D
	Matte Deep Black [ 107 ] Finish Type : Powder Coated Description : RAL 9005, very deep and very matte
	Traffic White [ 070 ] Finish Type : Powder Coated Description : RAL 9016
	BRONZE FINISHES : TECTUS® hinges now come in 3 new Bronze finishes. Please call us for details and pricing.
	CUSTOM FINISHES : TECTUS® hinges can be custom finished (e.g. 24k gold plating, hot pink powder-coated). For custom RAL colors or finishes, please contact us for pricing and minimum quantities.